2-1/2"x4-11/16"x1-1/16", weighs 270 grams (9-1/2 oz.), 24-40 NiMH/NiCd, 6-14 Li-Poly, 18-59V. Two sets of 4mm input cables (2 positive and 2 negative cables), 4mm output cables. Due to the high voltage the SPIN200 has an ancillary circuit that prevents sparking when the controller is being connected to the flight batteries. The negative poles of the flight pack must be plugged to the two 4mm black wires first, then the thin (1.5mm) red wire must be plugged into the positive side of the flight pack. Only then can the two 4mm red wires be plugged into the flight pack. The controller has two 2-1/2"x2-1/2"x3/16" heat sinks and four standoff mounts to allow free airflow around all sides of the unit. No connectors are included. SPIN controllers can be programmed from your transmitter but for quicker setup and fine tuning you need to purchase a SPIN Box. All SPIN controllers are Data Logging controllers, they measure and capture readings for Max/Min controller temp, Max/Min current during use and when it occured, Cut-off voltage and the time it occured, Motor run time, Maximum motor RPM and the time it occured. These Data Logging features greatly enhance your ability to fine tune the power system on your airplane to get the maximum performance yet protect yourself from damaging your equipment by having the wrong setup. To be able to fine tune your setup and check the logged data that your SPIN Controller captures you need to purchase the SPIN Box. It is the one tool that allows you to change settings and read out data all without the need to connect to a computer, great for flying field. Technical Specifications: | Voltage Range: | 18V - 59V | | BEC Amperage: | No BEC | | BEC Type: | No BEC | | Constant Current: | 170 Amps |
|
JETI MOTOR CONTROLLER WARRANTY AND REPAIR POLICY
Hobby Lobby has a 2-Year warranty period form date of purchase for JETI Motor Controllers.
Note: Hobby Lobby is the USA agent for JETI. All Hobby-Lobby/JETI Motor Controllers have Hobby Lobby's name printed on the back of the controller under the plastic shrink wrap. Hobby Lobby will not take responsibility for JETI Motor Controllers which do not contain the Hobby Lobby imprint.
If purchased from Hobby-Lobby:
Within warranty period:
If you purchased your JETI Controller direct from Hobby Lobby, Hobby -Lobby will replace it at no charge if it fails to operate within the first 730 days. We must have the unit returned before we can replace it. Exception: If you connect your battery to your JETI Controller backwards, that is, with the positive lead from your battery connected to the negative input lead of the JETI Controller, the controller will burn out. This failure is not covered under Hobby-Lobby's warranty, but will be handled as an after warranty period replacement.
After the warranty period:
If your JETI Motor Controller quits working, Hobby Lobby will replace it at a cost of 1/2 the current retail price of the unit upon it being returned to us.
If not purchased from Hobby Lobby:
If you purchased your JETI Motor Controller from a hobby shop, and it has the Hobby Lobby imprint under the shrink wrap, and it fails or is in need of repair, take it back to the hobby shop for repair/replacement. Hobby-Lobby will then replace the controller to the hobby shop according to our warranty policy.
If it is within warranty period and fails, other than the failure caused by connecting the batteries in reverse, the hobby shop should give you a new JETI Controller at no charge.
If it is out of the warranty period or you did something to cause it to fail, your hobby shop should sell you another one at half price.
Attention Hobby Shop Owner:
Hobby Lobby will replace any Hobby Lobby/JETI motor controller you send back to us that you have taken back from and replaced for your customer. If the failure was within the warranty period, Hobby Lobby will replace the controller at no charge. If the failure was caused by customer error (connecting the batteries in reverse), or it is out of the warranty period, Hobby-Lobby will replace it at half price.
|
Cart Items 0
FAQs
