Hobby
Tools for Model Airplanes,
Boats and RC Helicopters
Boats and RC Helicopters
|
Hobby
Tools for Model Airplanes,
Boats and RC Helicopters |
| Home | Electric Airplanes | |
 Precision Metric slotted screwdriver set |
|
 |
6-7/8" long slotted metric screwdriver set has long shank, great for any modelers toolbox. Quality tool steel with precision ground tips. Blade widths at tip are 2.0mm, 2.4mm, and 3.0mm. |
Machined tempered steel shafts for a solid, no strip fit |
|
 |
5-3/8" long with color-coded knurled handles. Metric sizes 1.5mm, 2.5mm, 3mm, 3.5mm. |
Machined tempered steel shafts for a solid, no strip fit |
|
 |
3-5/8" long x 3/4" dia. handle with 4 metric hex wrenches inside. The handle is carbon fiber tube with anodized aluminum ends. Handle contains 1.5mm, 2mm, 2.5mm, and 3mm hex wrenches machined from 3.5mm hardened steel shafts. Assembled length is 6-1/8". Light and easy to carry, great for the field box. |
Metric nut drivers with long shank make easy work of loosening nuts |
|
 |
6-7/8" long metric nut drivers. Great for working on helicopter blade grips and locking nuts. |
| Metric Hex Drivers with long shank and comfort grip make removing hex screws easy |
|
 |
6-7/8" long metric hex drivers. Great for removing stubborn metric hex head screws. Precision machined from hardened steel for perfect fit. Tip sizes are 1.5mm, 2.0mm, 2.5mm and 3.0mm. |
Cut 1mm to 14mm diameter holes in wood, fiberglass, or plastic |
|
 |
Hardened steel Super Reamer easily drills holes in plastic canopies and fiberglass cowls without tearing the material like a drill bit does. Has a carbon fiber handle and an aluminum cap to protect the tip while not in use. |
Perfect Z-Bends every time |
|
 |
Most kits and ARF kits still leave the job of bending the pushrod ends up to you. Make perfect light-weight pushrod Z-bend connections for servo and control horn hookups in music wire up to 1/16" (1.5mm). |
A must for every helicopter pilot |
|
 |
Makes installing, removing and adjusting ball links very easy. |
High quality precision tools for all modelers |
|
 |
Top quality tool-steel pliers precision ground to a fine point for reaching into small spaces. Serrated jaws hold small parts securely. |
For electrical and plastic cutting |
|
 |
Light duty cutters with rubber grips for electrical wiring. Ideal for cutting servo leads and electrical wires on motors and speed controls. Also great for cleanly cutting plastic parts off of a parts tree. Not made for cutting music wire. |
For electrical and plastic cutting |
|
 |
Cuts music wire up to 5/64" with ease. Great for cutting pushrods without leaving sharp ends. Cuts are square ended and much easier to make than with side cutters. Comfortable rubber grips. |
Special scissors for ABS plastic |
|
 |
5-1/2" long, extremely sharp, with slightly curved blade. Expressly for cutting thin plastic canopies, wheel pants, cowls, vacuformed styrene parts, etc. |
Detects slightest breeze from any direction! |
|
 |
|
Pinion puller SPEED 400 to
SPEED 600 size motors |
|
 |
Tool
has 3 set screws: one blunt end, one with 2mm and one with 3mm shafts
for pushing out the motor shafts from pinion gears. Works on all 2.3mm
motor shafts (SPEED 400's) and all 3.2mm motor shafts (SPEED 500,
600). |
|
|
|
| Ever wish you had an extra hand? |
|
 |
3-3/4" x 2" x 1/2", weighs about an ounce. Constructed of black leather with a Velcro catch on one side and a belt clip on the other. Makes it easy to carry your transmitter on your belt while carrying your plane and toolbox out to the flight-line. Easily remove your radio from the "Hip Clip" with one hand. Rugged design for years of trouble-free use. |
This prop balancer is so sensitive that you can even balance your prop nut! |
|
 |
About 4" high. This balancer has friction free rotors with steel axles. Any size propeller from a 1" diameter boat prop to a 24" airplane prop can be clamped onto the rotor by the conical shaped self-centering clamps on its rotor. Sand off material on the back side of the heavy blade. We are not kidding about balancing prop nuts — it can! |
|
|
|
| Low prices on knives and tool sets! | |
 |
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
 |
|
|
|
|
 |
|
|
|
|
Tip Drill has 12 drill bits inside the handle |
|
 |
4"
long, comes with 12 bits sizes 52-74 (the largest is 1/16" dia.).
The easiest way to drill small holes, better than a crank tool or Dremel
for small holes. |
Test and center your servos before you install them |
|
 |
Tiny 1-3/8 x 7/16 x 7/8", 8 grams. Servo adjuster allows you to connect 1 or 2 servos for centering or testing without the use of a receiver and transmitter. Connect any 4-5 cell receiver pack for power, plug in your servo(s), rotate the knob to test the travel then return the knob to the middle to center your servos. |
Checks voltage of 4-10 cell NiCad/NiMH or 1-3 LiPo packs |
|
 |
About 2-1/4 x 1-5/8 x 5/8", 1.3 oz., Large easy-to-read 3/8" LCD display indicates voltage of any battery pack 4-13 Volts DC instantly. Use with 4-10 cell NiCad and NiMH packs or 1-3 LiPo cells. Accurately check the voltage of your receiver pack before you fly. |
Extremely accurate temperature readings - instantly! |
|
 |
Approximately 3-1/4" long x 3/4" dia. Extend the life of your LiPo batteries, speed controls and motors by checking the temperature after flights making sure to operate them within the manufacturers recommended temperature ranges. This is a non-contact infrared thermometer, just aim the unit at the target and press the measure button to display the surface temperature. The measurement range is from –27.4 to 428 degrees F (-33 to 220 degrees C) with an accuracy of +/- 2%. Compact, comes with pocket clip and batteries. Auto shut-off after 15 seconds. |
Measure and improve performance of your electric flight system! |
|
 |
Both: 4-1/16 x 2-3/16 x 15/16", about 4 oz. Measure your motor's and battery's Volts (to 60V), Amps (to 100A), Watts (up to 6000), Amp-Hours (up to 9.999AH), and Watt-Hours (up to 999.9WH). Plug in Power Analyzer between your battery and motor controller to measure your system's performance. Easy to use with good instructions. Power Analyzer PLUS II can be connected to your computer's USB port with the included interface cable and its software (on CD). All of your tests can be saved and graphed on your computer. Track the changes in battery packs over time or optimize the prop and battery selection for your next plane. (Photo shows Power Analyzer Plus. Cable and CD are only included with this version.) Units come without connectors; order ones that match your systems. |
Cart | Home | E-Flight Accy | Glow Accy | Micro Hobby Lathe | Product Index | Catalog | Contact Us
Phone: 1-866-WE-FLY-RC (1-866-933-5972)
Fax: 615-377-6948
Copyright © 1996-2008 Hobby Lobby International, Inc. All Rights Reserved.
2-1/8" wide, 5" tall, 1-1/2" thick, tripod thread at base for stationary use. Want to know how fast the wind is blowing at your field or slope? This handheld wind meter is omni-directional and accurately measures the wind speed without orienting the unit into the wind. The large LCD display shows the current wind speed, maximum wind speed, average wind speed and a bar graph of current Beaufort values. Wind speed can be measured in miles/hour, kilometers/hour, meters/second, knots. The range of measurement is from 1-1/2 to 93 MPH. Comes with battery (approx 10 year life) and a Nylon protective bag.
