Advanced programming, allows you to operate up to 7 analog or 6 digital servos When performance matters in your high-current applications look no further than the E-flite® 60-Amp Pro Switch Mode ESC. This is a high-quality, efficient sensorless brushless electronic speed control with an integrated Switch-Mode BEC. It can operate without the need for a separate receiver battery to power your servos and receivers, saving you weight and complication. It is capable of up to 60 amps continuous current when using 3 to 6 series LiPo battery packs. You can drive up to 7 analog or 6 digital standard-sized servos with the BEC on any recommended input voltage. Featuring an exposed, finned heat sink aluminum case with lightweight plastic endcaps, safe power-arming along with advanced programmable features such as low voltage cutoff, braking, timing, throttle input range, and more, the E-flite 60A Pro Switch Mode ESC is truly a 'pro series' electronic speed control.
60A Pro Switch-Mode BEC Brushless ESC Highlights:
- Up to 60 amp continuous current with proper air flow, 75 amp peak
- 5-volt Switch-Mode BEC circuit capable of 2.5-amp continuous current on any recommended input voltage
- Drives up to 7 analog or 6 digital standard-sized servos, with the BEC on any recommended input voltage
- 3-6S LiPo, 9 to 18 cell NiCd/NiMH input voltage
- Finned heat sinks
- Programmable motor braking
- Safe power arm mode prevents accidental starts
- Programmable low voltage cutoff with settings for 3 cell LiPo (9V), 4 cell LiPo (12V), 5 cell LiPo (15V), 6 cell LiPo (18V), or 70% of battery starting voltage
- Programmable soft start for helis and airplanes
- Auto motor shut down if signal is lost or there is interference
- Programmable timing 5 user selectable ranges for use with a larger variety of brushless motors
- Programmable throttle input range (1.1-1.9 ms or 1.2-1.8 ms)
- Utilizes new smaller MOSFETs technology to minimize weight
- Radio System Power On/Off Switch
- Optional RS232 Serial Link available for programming
- Pre-wired connectors-E-flite EC3 on battery input and 3.5mm female gold bullets on motor output leads
60A Pro Switch-Mode BEC Brushless ESC Specs:
- Brake: Yes - Programmable
- Continuous Maximum Current: 60A with reasonable cooling
- Input Voltage: 10.8V - 22.2V
- Input Connector Types: 13AWG with E-flite EC3 connector
- Output Connector Types: 13AWG with 3.5mm Female Gold Bullet Connectors
- Momentary Peak Current: 75A (15 sec)
- Length: 3.00 in. (76mm)
- Width: 1.30 in. (33mm)
- Height: 0.50 in. (13mm)
- Weight: 2.3 oz. (66g)
- Wire Gauge: 13AWG
- Cells w/BEC: 3-6S LiPo or 9-18 NiMH/NiCd
60A Pro Switch-Mode BEC Brushless ESC Specs:
- Brake: Yes - Programmable
- Continuous Maximum Current: 60A with reasonable cooling
- Input Voltage: 10.8V - 22.2V
- Input Connector Types: 13AWG with E-flite EC3 connector
- Output Connector Types: 13AWG with 3.5mm Female Gold Bullet Connectors
- Momentary Peak Current: 75A (15 sec)
- Length: 3.00 in. (76mm)
- Width: 1.30 in. (33mm)
- Height: 0.50 in. (13mm)
- Weight: 2.3 oz. (66g)
- Wire Gauge: 13AWG
- Cells w/BEC: 3-6S LiPo or 9-18 NiMH/NiCd
Please call our support line toll free: (866) 512-1444 for assistance with this product |
Cart Items 0
FAQs
