Adhesives,
Glues & Epoxy for RC Models
|
Adhesives,
Glues & Epoxy for RC Models
|
| Home | Electric Airplanes | Glow Airplanes | |
| Zap Superior CA Glue | |
 |
|
Devcon Epoxy Glues, Thread lock
 Epoxy Adhesives |
|
NEW! Glues nearly anything to anything, and it's waterproof |
|
 |
Creates a strong waterproof bond to nearly anything. Great for gluing spars in foam wings. Its foaming action fills small voids for a super strong bond. Use anywhere that you need a lightweight joint with great strength. Mist the bonding area with a small amount of water before applying SAG to the part, then join and apply pressure. Forms a strong bond in as little as three hours, cures completely after 24 hours. Unlike other polyurethane glues of this type, it foams only slightly. |
| Deluxe Materials Glues | |
A glue that works better than CA  |
What does it do? It glues woods together BETTER than any other glue. Why? It flows inside the grain of the two pieces of wood, grabs hold of the grain from the inside, then it connects the pieces so strongly that they can only be parted by breaking the wood. It’s not as fast setting as CA but it makes much stronger joints and it is almost weightless when dry.
|
|
Best
glue for attaching airplane canopies
|
4 oz. bottle of VERY tacky glue that goes on white and dries CLEAR. Shut-off dispenser top leaves a precise bead of glue. The glue shrinks as it dries and becomes clear and does not get brittle. The clear plastic canopy stays on and you can’t see the glue. Glues other hard-to-glue things also, like fabrics, foil, metal, glass. |
|
|
|
 UHU-Hart: "Airplane Glue" - it’s very fast setting and glues ABS plastic! Absolutely clear, ultra lightweight and strong when dried. This is the best selling model airplane cement in Germany. It dries so fast on balsa joints its almost like using CA. It is extremely strong and light. It slightly melts ABS plastic so it makes both a glue bond and a “weld” on ABS parts like boat hulls and airplane plastic fuselages. |
STABILIT
EXPRESS: As an adhesive Stabilit Express will firmly adhere anything to anything else. It is unsurpassed for joining such critical things as a nylon bellcrank to a fiberglass fuselage, or metal or plastic tubes to plastic or fiberglass. It is a two part methylacrylic adhesive. The material sets in only 20 minutes into a wood-colored mass. The fully cured material can be sanded and finished. The cured material has both compression and tensile strength, so it can be used as a structural element in addition to simply bonding other structures. |
|
PFM
glues anything to anything!
 |
PFM
is a one part, quick setting adhesive and sealant that glues just about
anything to anything else. It will melt foam however. It sets in about
30 minutes. PFM sets but doesn't get brittle; it will give without letting
go. PFM is non-flammable. PFM can repair electrical insulation, give strain relief to electric connectors, glue servos in place, glue servo trays and bulkheads in fiberglass fuselages. PFM is the indispensable glue in your workshop, thousands of uses and counting. |
Cyanoacrylate glue for foam models |
|
 |
Low odor, fills gaps well, dries in about a minute. |
Glue ABS to ABS or to wood |
|
 |
|
|
Glue
for styrofoam
 |
1.4 oz. tube (40 grams). Does not melt foam. Works primarily as a contact glue, apply thin layer to both mating surfaces, allow to set for 10 minutes, then press together. Make sure you are correctly aligned before touching pre-glued parts together, part will be difficult to re-position. Will glue anything to foam or foam to itself. Dries fast. |
Cart | Home | Product Index | Low Price Guarantee | Catalog | Contact Us
Phone: 1-866-WE-FLY-RC (1-866-933-5972)
Fax: 615-377-6948
Copyright © 1996-2008 Hobby Lobby International, Inc. All Rights Reserved.
