Jason Says:

"Simply the best design I've seen! No more hassle to get the wings on and off, amazing. "

Senior Telemaster Kit V2 - Laser cut perfection

Completely re-engineered for a great build experience. We retained all the terrific flight characteristics of the original Senior Telemaster while adding all the features that our customers have been asking for. Battery or fuel tank access is through a large hatch on the top front of the fuselage. The wings are 2-piece and slide onto a large 1/4" x 1" aluminum spar joiner. The wing connection to the fuselage is with our unique rotate-and-snap system; it takes only seconds to install the wings and there are no loose parts to lose or forget. The vertical and horizontal tail assembly is removable as a unit and because the servos for elevator and rudder are in the stabilizer, there are no pushrods to disconnect; just unplug the servo extensions and four mounting screws.

The Senior Telemaster Kit includes a drop box: a large hatch on the bottom of the fuselage can be remotely opened by a servo for candy drops or parachute drops. The fuselage interior is large with lots of room for a camera. When the drop door is opened it swings to the rear and is held open by magnets. The precision of laser cutting brings a whole new experience to kit building, parts fit precisely and assembly is much faster than with earlier style kits. Full size black line prints and a 30-page photo-illustrated instruction manual guide you through the build with each step clearly covered. You can be assured of a warp-free, light yet strong aircraft that retains all of the great flying characteristics that makes the Senior Telemaster the iconic model aircraft that it is. The Senior Telemaster is a great match for the TEL1425 Float Kit. The rear attachment point for float operation is supplied in the kit.

Kit includes strong aluminum landing gear and bent wire tailwheel assembly, pushrods and clevises. Axels, main wheels and tail wheel not included. You will need 4 rolls of covering. A 6-channel radio system is required to use all functions: Ailerons (2 servos), Flaps (2 servos), Elevator, Rudder (2 HS-225 servos), Drop hatch (eRC 9g servo).

Tech Specs:
Wingspan: 91-1/2"
Length: 63-1/4"
Wing area: 1301 sq. in.
Flying weight (w/5s 5000mAh): 10-1/2 pounds
Motor: 60 size brushless outrunner
Battery: 5 cells 5000mAh LiPo
Speed Control: 85A Opto
Servos (Ailerons and Flaps): 4-Standard HS-322 or equiv.
Servos (Elevator and Rudder): 2-HS-225MG
Servo (Drop Hatch): 1-eRC 9g

What's New in the Senior Telemaster V2 Kit:
All laser cut precision balsa and plywood
2-piece wing for easy transport
Large strong aluminum spar joiner (no struts required)
Removable tail group (undue 4 bolts and 2 electrical connections)
Included drop box for added fun
Includes mounting point for float operation

Senior Telemaster Discussion:
Click HERE to join the building discussion as well as see tips and tricks.

Building Videos:

Radio
1 - SPM7800 DX7s Transmitter Only
4 - HRC31422S HS-322 Standard Servos
2 - HRC32225S HS-225MG Servos
1 - ERCS900 eRC 9g Servo
6 - HRC54604S 12" Servo Extension
2 - HRC54605S 24" Servo Extension
2 - HRC57347S 36" Servo Extension
1 - HRC57351S Dual Y Harness Servo Extension

Motor/Prop
1 - ERCBL60 eRC .60 Brushless Motor
1 - APC17010E 17x10E Thin Electric Prop

Motor Controller
1 - ERCE085P eRC 85A Opto Brushless ESC
1 - ERCE02 eRC Electronic Programmer
1 - ERCBEC6 eRC 6A BEC

Battery
1 - VNR15021 5S 5000mAh Lipo

Charger
1 - DYN4105 Passport UltraForce 200WAC/DCCharger

Accessories
Glue, Solder, Connectors, etc and four rolls of covering material.

Senior Telemaster Kit V2 Manual