Servo Mounts (Mounting) and Pushrod Exit Covers for Sailplanes from Hobby Lobby!

Easy to install wing servo system
	HT0098 Wing Mount "Can" for Micro Servos, 2 ..... $ 8.90 AVAILABLE NOW Clean installation for small servos in a wing or tail. Allows easy access to the servo for adjustment or repair. Made for servos of similar size to Hitec’s HS-85BB. Included are adapters to fit Airtronics 94501, JR 341, Futaba S143.

You can install MINI and MICRO servos in thin wings, and REMOVE them with these servo FLAT MOUNTS!
Servo Flat Mounts allow the servo to lie with its side flat against the bottom so the servo installation will take up no more depth than the actual thickness of the servo itself. About 1" long and 1/2" high, 2 pairs per pack with 4 screws and washers. In a thin wing the aileron servos need to be mounted like this.	RA190 Servo Flat Mounts Mini, 2 pr. ..... $ 3.20 AVAILABLE NOW Servos can sometimes be mounted by this method inside fins and horizontal stabs. You can shorten the vertical legs to the thickness of your servo. Insert a small screw and washer into the hole in the leg to clamp the servo in place. The screw can also hold the access plate or a fairing in place on top of the servo. Fits all "mini" and "micro" servos.

Mount your servos right next to the flight control!
2-3/8" square white plastic plates with molded-in exit fairings. Fasten your servo to them. When you mount the plastic plate in place you have installed your servo. Standard size servos mount in the included servo mount.	RA200 Surface Mount System for Standard size Servos, pr. ..... $ 8.60 AVAILABLE NOW RA210 Surface Mounts for Mini Servos, pr. ..... $ 8.60 AVAILABLE NOW Same as RA200 but only 2" square. For mini servos up to 1-5/8" long (to ends of mounting tabs) such as Hitec HS-81.

2-side tape for servo mounting
	DUB634 Servo Mounting Tape Assortment 1/32, 1/16, 1/8" (2-side sticky) ..... $ 2.55 AVAILABLE NOW

Velcro for holding batteries, hatches in place
	VEL001 6" Velcro, Black ..... $ 2.10 AVAILABLE NOW

Control exit cover or airscoop
About 2" long. White plastic.	HLH550 Exit Cover/Airscoop, 2 ..... $ 3.30 AVAILABLE NOW Very easy to mount — glues onto surface. Good drag reducer. Reversed, it is an airscoop for electric flight.

Long, aileron pushrod fairings
These are drag-reducing fairings for the pushrods to any control surface — ailerons, elevator, flaps, rudder, speedbrakes, spoilers. The flat base of the pushrod fairing is 5" long overall.	HLAN9321 Aileron Pushrod Fairings, pr. ..... $ 3.80 AVAILABLE NOW The forward part of the base is molded with a downward bend so it won’t pull up in the airplane’s slipstream. The fairing itself is about 3-3/4" long and 5/8" high. Cut off the aft end of the Fairing to make the Fairing any length you want. One is shown cut off in the photo. The Fairings are molded of ABS plastic which can be glued or screwed down over the servo’s output arm.

These aileron pushrod fairings also cover the servo
	GR4269/6 Aileron Servo Covers, pr. ..... $ 11.90 ESTIMATED ARRIVAL 05/23/08 - Please Preorder Now 3" long. 2" wide, 3/4" high. Use part RA190 (Servo Flat Mounts) to mount the servos in the wings. You can bolt the Aileron Servo Covers onto part RA190.

Servo Mounts and Pushrod Fairings