HUGE - Tom Hunt calls it "Balsa Overcast"! |  |
143-1/2" wingspan, 90" long, 3050 sq. in. wing area (over 21 sq. ft.), 23 pounds flying weight, a little over 16 oz. per sq. ft. wing loading (and about 14 oz./sq. ft. when you count the lifting stabilizer). Laser cut wing ribs, aileron, stab and elevator ribs. Construction is conventional all balsa and plywood and the kit for this huge airplane is a veritable lumberyard. Nothing flies like a Telemaster! Its gentle handling character is legendary as is its ability to lift weight. This model can easily lift camera equipment or a camcorder and is so slow and stable that the photos and videos come out beautifully. It jumps off the ground with the recommended AXI 5330 Outrunner motor. Model is easy to build but requires a large area for construction. Wing is three-piece; center section is the width of the fuselage and bolts to it, the two wing panels bolt to the center section. The lift struts are functional and must be used. Wing panels can be built with flaps or without. Lifting stabilizer has an area of 672 sq. in. (larger than many airplane wings) and is removable for transport. Model can also be powered by a gas engine like the Zenoah G-26. Also available as a 12 Foot Telemaster ARF. 12 Foot Telemaster PDF Instruction ManualTechnical Specifications: | Length: | 90" | | Wingspan: | 143-1/2" | | Flying Weight: | 23 lbs. | | Controls: | Ailerons, Elevator, Rudder, Flaps, Throttle | | Wing Area: | 3050 sq. in. |
|
It's a project to build! but is very docile to fly I installed a Zenoha G 38 tons of power but not over powered! You got to fly this one with rudder so couple it with ailerons for best results.... This one is going to be a Sky Diver hauler and a video camera platform. Have a ton of pic Thanks for a Great kit
|
Kit contains great quality wood with enough extra wood to build another small plane. Plans are clear and well laid out. Assembly manual could use a tad bit of improvement. Hardware package needs control horns & tail wheel bracket. I enjoyed building the kit (very relaxing). I installed Fuji G50 engine, landing & nav lights, candy hopper, glider & banner tow release, two skydiver mounts and Flycam2 video camera (uses same mount as skydiver).
I would not recommend this kit for the first time builder.
|
Had a good time building this monster. It takes a large area to build on,but it was worth the effort.I would advise anyone building it, to take your time.The plans are great,and easy to follow.Get one of these,and get started on your summer flying now.By the way the wood in this kit is the best I have seen in a while.
|
|
Read All Reviews...
|
Here's Everything You'll Need: Radio 1 - SPM7800 DX7s 7 Ch w/ AR8000 NO SX's MD2 1 - HTS0422 Hitec HS-422 Servo 1 - HT0604 12" Aileron Extension w/Gold Pins 4 - HT0605 24" Aileron Extension w/Gold Pins 4 - HT0606 36" Aileron Extension w/Gold Pins 2 - HRC57351S Dual Aileron Y Harness Servo Extension 1 - SPMB1500NM 1500mAh 4.8V NiMH Receiver Pack Motor/Prop 1- PM534514HD AXI 5345/14 HD Gold Line 1 - PE22010E 20x10E Thin Electric Prop Motor Controller 1 - ERCE085P eRC 85A Brushless Programmable Opto ESC 1 - ERCE02 eRC Electronic Programmer Battery 2 - TP50005SPL2 5 Cell 18.5V 5000 mAh Pro Lite V2 LiPo 1 - WSD7002 Series Module with Deans Ultra Connectors Charger 1 - SRC6200 B6 Ultimate 200 Watt Balance Charger Accessories Glue, Solder, Connectors, etc.Please call our support line toll free: (866) 512-1444 for assistance with this product |
Cart Items 0
FAQs
